Journal of Applied Science and Engineering

Published by Tamkang University Press

1.30

Impact Factor

2.10

CiteScore

U.T. Vinothraj and M. Anthony XaviorThis email address is being protected from spambots. You need JavaScript enabled to view it.

School of Mechanical Engineering, Vellore Institute of Technology, Vellore, Tamil Nadu- 632014, India


 

Received: October 19, 2023
Accepted: December 18, 2023
Publication Date: February 19, 2024

 Copyright The Author(s). This is an open access article distributed under the terms of the Creative Commons Attribution License (CC BY 4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are cited.


Download Citation: ||https://doi.org/10.6180/jase.202412_27(12).0001  


Additive manufacturing (AM) is a key component in several strategic sectors, such as the automotive, aerospace, and healthcare industries. It builds the production of near-shape components and is capable of consolidating multiple assembly components into a single unit. Metal additive manufacturing produces high-quality components that replace conventional manufacturing. Metal additive manufacturing processes, such as powder bed fusion techniques, exhibit superior mechanical properties, especially in wear and friction applications. In this study, we have fabricated the components using optimal parameters through laser Powder Bed Fusion and explored the behaviour of Wear and Friction of additive-manufactured stainless steel 316L. The experiments were conducted using a Pin-on-disc machine with varying loads of 5N to 30N with the subsequent testing parameters. Minimum wear and friction rate occurs in 5N and 10N loads, whereas there is a maximum wear and friction rate in 20N and 30N. Surface roughness properties of before wear and after wear were studied in an Optical microscope, Atomic Force Microscope (AFM), Field Emission Scanning Electron Microscope and the subsequent EDX elemental mapping was analyzed, the crystallographic orientation of additive manufactured SS316L was examined by using Electron Back Scattered Defragmentation (EBSD). Surface hardness properties were studied using Vickers’s microhardness. Material characterization of additive-manufactured stainless steel SS316L was examined using XRD for Residual stress present during the powder bed fusion process.

 


Keywords: Additive manufacturing (AM), Powder bed fusion, Stainless Steel 316L, Pin-on-disc, Wear and Friction, Microstructure study


  1. [1] U. M. Dilberoglu, B. Gharehpapagh, U. Yaman, and M. Dolen, (2017) “The Role of Additive Manufacturing in the Era of Industry 4.0" Procedia Manufacturing 11: 545–554. DOI: 10.1016/j.promfg.2017.07.148.
  2. [2] R. Groarke, C. Danilenkoff, S. Karam, E. McCarthy, B. Michel, A. Mussatto, J. Sloane, A. O. Neill, R. Raghavendra, and D. Brabazon, (2020) “316l stainless steel powders for additive manufacturing: Relationships of powder rheology, size, size distribution to part properties" Materials 13: 1–19. DOI: 10.3390/ma13235537.
  3. [3] Z. Wang, T. A. Palmer, and A. M. Beese, (2016) “Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing" Acta Materialia 110: 226–235. DOI: 10.1016/j.actamat.2016.03.019.
  4. [4] J. L. Coughlin, T. G. Hicks, P. S. Dougherty, and S. A. Attanasio. “Development and testing of 316L stainless steel metal additive manufacturing test articles for powder bed fusion and directed energy deposition processes”. In: STP 1620. ASTM International, 2020, 250–277. DOI: 10.1520/STP162020180109.
  5. [5] G. Maculotti, E. Goti, G. Genta, L. Mazza, and M. Galetto, (2022) “Uncertainty-based comparison of conventional and surface topography-based methods for wear volume evaluation in pin-on-disc tribological test" Tribology International 165: DOI: 10.1016/j.triboint.2021.107260.
  6. [6] S. KC, P. D. Nezhadfar, C. Phillips, M. S. Kennedy, N. Shamsaei, and R. L. Jackson, (2019) “Tribological behavior of 17–4 PH stainless steel fabricated by traditional manufacturing and laser-based additive manufacturing methods" Wear 440-441: DOI: 10.1016/j.wear.2019. 203100.
  7. [7] H. Zhang, Y. Pan, Y. Zhang, G. Lian, Q. Cao, J. Yang, and D. Ke, (2022) “Effect of laser energy density on microstructure, wear resistance, and fracture toughness of laser cladded Mo2FeB2 coating" Ceramics International 48: 28163–28173. DOI: 10.1016/j.ceramint.2022.05.399.
  8. [8] S. Yu, Y. Liu, R. Zhang, X. Ge, J. Li, X. Tang, and W. Wang, (2023) “Lubrication and anti-wear behavior of duplex annealed nanodiamonds/PEO coating on Ti6Al4V: Functional mechanism of structural transformation" Surface and Coatings Technology 461: DOI: 10.1016/j.surfcoat.2023.129426.
  9. [9] S. Mozammil, E. Koshta, and P. K. Jha, (2021) “Abrasive Wear Investigation and Parametric Process Optimization of in situ Al–4.5 % Cu–xTiB2 Composites" Transactions of the Indian Institute of Metals 74: 629–648. DOI: 10.1007/s12666-020-02180-8.
  10. [10] S. R. Pearson, P. H. Shipway, J. O. Abere, and R. A. Hewitt, (2013) “The effect of temperature on wear and friction of a high strength steel in fretting" Wear 303: 622–631. DOI: 10.1016/j.wear.2013.03.048.
  11. [11] E. J. Garboczi and N. Hrabe, (2020) “Particle shape and size analysis for metal powders used for additive manufacturing: Technique description and application to two gas-atomized and plasma-atomized Ti64 powders" Additive Manufacturing 31: DOI: 10.1016/j.addma.2019.100965.
  12. [12] T. Simson, A. Emmel, A. Dwars, and J. Böhm, (2017) “Residual stress measurements on AISI 316L samples manufactured by selective laser melting" Additive Manufacturing 17: 183–189. DOI: 10.1016/j.addma.2017.07.007.
  13. [13] P. L. Menezes, Kishore, and S. V. Kailas, (2009) “Influence of inclination angle of plate on friction, stick-slip and transfer layer-A study of magnesium pin sliding against steel plate" Wear 267: 476–484. DOI: 10.1016/j.wear.2008.12.078.
  14. [14] B. Podgornik, M. Šinko, and M. Godec, (2021) “Dependence of the wear resistance of additive-manufactured maraging steel on the build direction and heat treatment" Additive Manufacturing 46: DOI: 10.1016/j.addma.2021.102123.
  15. [15] M. Maher, I. Iraola-Arregui, H. B. Youcef, B. Rhouta, and V. Trabadelo. “The synergistic effect of wearcorrosion in stainless steels: A review”. In: 51. Elsevier Ltd, 2021, 1975–1990. DOI: 10.1016/j.matpr.2021.05.010.
  16. [16] W. J. Lai, A. Ojha, Z. Li, C. Engler-Pinto, and X. Su, (2021) “Effect of residual stress on fatigue strength of 316L stainless steel produced by laser powder bed fusion process" Progress in Additive Manufacturing 6: 375– 383. DOI: 10.1007/s40964-021-00164-8.
  17. [17] A. S. Wu, D. W. Brown, M. Kumar, G. F. Gallegos, and W. E. King, (2014) “An Experimental Investigation into Additive Manufacturing-Induced Residual Stresses in 316L Stainless Steel" Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science 45: 6260–6270. DOI: 10.1007/s11661-014-2549-x.
  18. [18] P. Jeyapandiarajan, U. Vinothraj, J. Dasari, J. Joel, M. A. Xavior, S. P. Natarajan, and A. Duchosal, (2023) “Investigation on post processing techniques oriented towards strength improvement of 3D printed SS316L" Materials Today: Proceedings: DOI: 10.1016/j.matpr.2023.05.049.
  19. [19] A. Saboori, G. Piscopo, M. Lai, A. Salmi, and S. Biamino, (2020) “An investigation on the effect of deposition pattern on the microstructure, mechanical properties and residual stress of 316L produced by Directed Energy Deposition" Materials Science and Engineering: A 780: DOI: 10.1016/j.msea.2020.139179.
  20. [20] S. Gao, Z. Hu, M. Duchamp, P. S. R. Krishnan, S. Tekumalla, X. Song, and M. Seita, (2020) “Recrystallizationbased grain boundary engineering of 316L stainless steel produced via selective laser melting" Acta Materialia 200: 366–377. DOI: 10.1016/j.actamat.2020.09.015.
  21. [21] N. Jeyaprakash, C. H. Yang, and K. R. Ramkumar, (2021) “Correlation of Microstructural Evolution with Mechanical and Tribological Behaviour of SS 304 Specimens Developed Through SLM Technique" Metals and Materials International 27: 5179–5190. DOI: 10.1007/s12540-020-00933-0.
  22. [22] G. Saha, K. Valtonen, A. Saastamoinen, P. Peura, and V. T. Kuokkala, (2020) “Impact-abrasive and abrasive wear behavior of low carbon steels with a range of hardness-toughness properties" Wear 450-451: DOI: 10.1016/j.wear.2020.203263.
  23. [23] H. Xiao, Y. Li, W. Xiao, C. Liu, P. Xie, and L. Song, (2023) “Grain structure and texture control of additive manufactured nickel-based superalloy using quasicontinuous-wave laser directed energy deposition" Additive Manufacturing 69: DOI: 10.1016/j.addma.2023.103520.
  24. [24] S. Dryepondt, P. Nandwana, P. Fernandez-Zelaia, and F. List, (2021) “Microstructure and high temperature tensile properties of 316L fabricated by laser powder-bed fusion" Additive Manufacturing 37: DOI: 10.1016/j. addma.2020.101723.


    



 

2.1
2023CiteScore
 
 
69th percentile
Powered by  Scopus

SCImago Journal & Country Rank

Enter your name and email below to receive latest published articles in Journal of Applied Science and Engineering.