Duo Yang This email address is being protected from spambots. You need JavaScript enabled to view it.1, Tianding Chen1, and Chengfei Rao1

1School of Mechanical Engineering, Dalian University, Dalian 116622, China


 

Received: April 1, 2021
Accepted: August 6, 2021
Publication Date: September 11, 2021

 Copyright The Author(s). This is an open access article distributed under the terms of the Creative Commons Attribution License (CC BY 4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are cited.


Download Citation: ||https://doi.org/10.6180/jase.202204_25(2).0013  


ABSTRACT


As chatter vibration in roll grinding process is the largest limitation in surface quality of machined roll. In this paper, the bistability analysis and chatter suppression are performed for further discussion of patterns of the grinding chatter to reduce the cost of enterprises. A new three degrees of freedom dynamic model with both the regenerative effect and nonlinear stiffness of grindstone indicated by Duffing oscillator is presented, and its availability is validated by the experiment. By means of the DDE-BIFTOOL, a numerical calculation package, the effect of process parameters on grinding stability is studied extensively, proving that a large grinding width worsens the stability in roll grinding and the parameters locating in unsafe areas should be avoided for a stable grinding operation in practice. In addition, the control techniques involving both the nonlinear velocity feedback and the chaos perturbation are proposed for the suppression of chatter vibration in grinding operation to decrease the amplitude of its vibration. The results show that these techniques give a significant performance for reducing the amplitude of chatter vibration, namely, the stability of grinding process is augmented, which give a new idea for firms in chatter suppression.


Keywords: Grinding, Regenerative chatter, Bistability, Chatter suppression, Chaos control


REFERENCES


  1. [1] L. Yuan, E. Keskinen, and V. Järvenpää. “Stability analysis of roll grinding system with double time delay effects”. In: IUTAM Symposium on Vibration Control of Nonlinear Mechanisms and Structures. Springer. 2005, 375–387.
  2. [2] Z. Liu and G. Payre, (2007) “Stability analysis of doubly regenerative cylindrical grinding process" Journal of Sound and Vibration 301(3-5): 950–962.
  3. [3] K.-w. Chung and Z. Liu, (2011) “Nonlinear analysis of chatter vibration in a cylindrical transverse grinding process with two time delays using a nonlinear time transformation method" Nonlinear Dynamics 66(4): 441–456.
  4. [4] Y. Yan, J. Xu, andW.Wang, (2012) “Nonlinear chatter with large amplitude in a cylindrical plunge grinding process" Nonlinear Dynamics 69(4): 1781–1793.
  5. [5] P. Kim, J. Jung, S. Lee, and J. Seok, (2013) “Stability and bifurcation analyses of chatter vibrations in a nonlinear cylindrical traverse grinding process" Journal of Sound and Vibration 332(15): 3879–3896.
  6. [6] Y. Yan, J. Xu, and M.Wiercigroch, (2016) “Regenerative and frictional chatter in plunge grinding" Nonlinear Dynamics 86(1): 283–307.
  7. [7] Y. Yao, J. Xu, and M. Wiercigroch, (2017) “Regenerative chatter in a plunge grinding process with workpiece imbalance" The International Journal of Advanced Manufacturing Technology 89(9-12): 2845–2862.
  8. [8] M. M. Jalili, R. Fazel, and M. M. Abootorabi, (2017) “Simulation of chatter in plunge grinding process with structural and cutting force nonlinearities" The International Journal of Advanced Manufacturing Technology 89(9-12): 2863–2881.
  9. [9] P. Lajmert, M. Sikora, and D. Ostrowski. “A dynamic model of cylindrical plunge grinding process for chatter phenomena investigation”. In: MATEC Web of Conferences. 148. EDP Sciences. 2018, 09004.
  10. [10] M. Tóth, N. D. Sims, and D. Curtis, (2019) “An analytical study of wheel regeneration in surface grinding" Procedia CIRP 82: 214–219.
  11. [11] J. Alvarez, D. Barrenetxea, J. Marquinez, I. Bediaga, and I. Gallego, (2011) “Effectiveness of continuous workpiece speed variation (CWSV) for chatter avoidance in throughfeed centerless grinding" International Journal of Machine Tools and Manufacture 51(12): 911–917.
  12. [12] J. Alvarez, M. Zatarain, J. Marquinez, N. Ortega, and I. Gallego, (2013) “Avoiding chatter in traverse cylindrical grinding by continuous workpiece speed variation" Journal of Manufacturing Science and Engineering 135(5):
  13. [13] A. H. Nayfeh and N. A. Nayfeh, (2011) “Analysis of the cutting tool on a lathe" Nonlinear Dynamics 63(3):395–416.
  14. [14] A. H. Nayfeh and N. A. Nayfeh, (2012) “Time-delay feedback control of lathe cutting tools" Journal of Vibration and Control 18(8): 1106–1115.
  15. [15] K. Fansen, L. Peng, and Z. Xingang, (2011) “Simulation and experimental research on chatter suppression using chaotic spindle speed variation" Journal of Manufacturing Science and Engineering, Transactions of the ASME 133(1): DOI: 10.1115/1.4003476.
  16. [16] P. Parenti, M. Leonesio, and G. Bianchi, (2016) “Modelbased adaptive process control for surface finish improvement in traverse grinding" Mechatronics 36: 97–111.
  17. [17] H. Moradian, M. H. Abbasi, and H. Moradi, (2020) “Adaptive sliding mode control of regenerative chatter and stability improvement in boring manufacturing process with model uncertainties" Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science 234(6): 1171–1181.
  18. [18] K. Engelborghs, T. Luzyanina, and D. Roose, (2002) “Numerical bifurcation analysis of delay differential equations using DDE-BIFTOOL" ACM Transactions on Mathematical Software (TOMS) 28(1): 1–21.
  19. [19] K. Engelborghs, T. Luzyanina, and G. Samaey, (2001) “DDE-BIFTOOL v. 2.00: a Matlab package for bifurcation analysis of delay differential equations" TW Reports: 61–61.
  20. [20] T. G. Molnár, T. Insperger, S. John Hogan, and G. Stépán, (2016) “Estimation of the bistable zone for machining operations for the case of a distributed cuttingforce model" Journal of Computational and Nonlinear Dynamics 11(5):


    
 

0.7
2020CiteScore
 
 
33rd percentile
Powered by  Scopus

SCImago Journal & Country Rank

Enter your name and email below to receive latest published articles in Journal of Applied Science and Engineering.